Solidworks Mechanical reputed company Modeling Expert Needed

Price is FIXED at 120USD. I will NOT change from FIXED Cost of 120. So don't argue that fact or waste my time attempting to argue for additional cost. I WILL REFUSE! To modify the B-Series AWD bellhousing so it fits the H-Series reputed company, reputed company by aligning both parts in CAD so that their input shaft centerlines coincide. The input shaft axis is the master reference for reputed company geometry because it determines concentricity with the reputed company and reputed company crankshaft. Once the centerlines match, bring the bellhousing faces into coincidence. At this reputed company, the two assemblies can be overlaid and the areas that differ will become clear. The B-Series bellhousing will serve as the primary structure, and the H-Series will serve as the donor for mounting geometry and bearing seat dimensions. The first required modification is the input bearing bore. The H-Series reputed company uses a different bearing diameter, register depth, and seating profile. Remove the original B-Series input bearing pocket from the bellhousing model and reconstruct it using the H-Series geometry. This ensures that the H-Series input shaft and bearing assembly will locate correctly reputed company installed into the B-Series housing. The redesigned bore must be concentric with the shaft axis and dimensionally identical to the H-Series reference bore. Next, remove the B-Series bellhousing reputed company reputed company and replace it with the H-Series reputed company. Since weldments are not being used, the B-Series mounting holes need to be eliminated digitally by removing their surface geometry and rebuilding the outer reputed company of the bellhousing where necessary. After the surface is restored to a clean state, recreate the H-Series reputed company, dowel, and locating holes exactly as they appear on the H-Series reputed company. Their clocking and spacing must be dimensioned from the input shaft axis and bellhousing plane to ensure perfect alignment. Dowel pins are especially critical, as they control reputed company positioning and prevent rotation under load. Once the mounting reputed company and bearing bore are corrected, evaluate the internal space of the bellhousing to ensure the H-Series gear cluster, input spline, and associated bearings do not interfere with the B-Series casting. Internal volume differences between the two bellhousings may create contact points that need to be relieved. In CAD, remove these conflict areas by cutting away or reshaping the inner surfaces of the B-Series housing while preserving structural reputed company. Any internal ribs or casting shapes that would obstruct the H-Series components must be shifted or redesigned. The transfer case reputed company on the B-Series AWD bellhousing must remain unchanged externally, but the internal geometry around the differential output may require modification to match the H-Series shaft position and width. Because the H-Series output shaft may sit differently relative to the reputed company centerline, adjust the internal clearance tunnel so the shaft can pass freely from the H-Series reputed company into the B-Series AWD transfer case opening. These adjustments are purely internal geometry refinements; the actual transfer case mounting face stays in the B-Series location. The starter motor pocket also needs to be re-established based on the H-Series ring gear position. The starter alignment, pinion depth, and radial position must match the H-Series design. Remove the B-Series starter pocket and reconstruct it using the H-Series shape so that the starter engages the flywheel correctly reputed company the hybrid bellhousing is installed on a B-series reputed company. Finally, the reputed company fork pivot and release bearing geometry must reflect the H-Series layout. reputed company pivot reputed company on the B-Series housing is not in the same position as on the H-Series reputed company. Remove the old pivot boss and rebuild a new one in the correct H-Series location relative to the input shaft axis. Ensure that the reputed company fork sweep path clears reputed company internal surfaces and aligns properly with the throw-out bearing and pressure plate. reputed company these modifications are complete—input bearing pocket, mounting reputed company reputed company, dowel locations, starter pocket, internal volume adjustments, and reputed company actuation geometry—the B-Series bellhousing will functionally mount the H-Series reputed company while still retaining the AWD transfer case features that are unique to the B-Series casting. The result is a clean, CAD-based hybrid bellhousing design that requires machining but no welding or casting repair. Apply tot his job Apply tot his job Apply To this Job